Meze 105 AER Headband Replacement: Fit and Care Guide

Quick answer

Replacing the headband on your Meze 105 AER is a straightforward swap: order the standard 105 AER Headband, remove the old band from the yokes, and fit the new one without overtightening. Work on a clean, soft surface, keep the screws paired with their original holes, and check the band sits evenly before you put the headphones back on. The whole job usually takes 10–15 minutes and needs only a small Torx driver.

What you need before you start

Gather the replacement headband, a T6 Torx driver, a soft cloth, and a shallow tray for screws. The 105 AER Headband is a standard replacement made from soft PU leather with a ‘105 AER’ logo engraving, so it is a direct fit for the 105 AER. If you are also replacing the spring band or screws, the LIRIC HEADBAND KIT includes a steel spring band and six M2 x 10mm T6 Torx screws, but those parts are sized for the Liric, not the 105 AER — check compatibility before mixing kits.

Step-by-step fitting

1. Power down and unplug. Remove the cable from the 105 AER so it cannot snag while you work. 2. Lay the headphones on a soft cloth with the ear cups facing up. 3. Locate the screws that hold the headband to the yokes. On the 105 AER these are small Torx screws; use a T6 driver and turn counter-clockwise. Common mistake: using a Phillips driver and stripping the screw head. 4. Remove the old headband and set the screws in your tray. 5. Align the new 105 AER Headband with the yoke holes, making sure the ‘105 AER’ engraving faces outward and reads correctly when worn. 6. Thread each screw in by hand first, then tighten gently with the driver. Checkpoint: the band should sit centered, with equal gap on both sides. 7. Reconnect the cable and test the fit on your head before fully tightening. 8. Once the fit is even, give each screw a final light snug — do not overtighten, as this can crack the yoke plastic.

Common mistakes to avoid

The most frequent error is overtightening the Torx screws; they only need to be snug, not torqued down. Another is fitting the headband backward — the logo engraving should face outward so it is visible when the headphones are on your head. If you drop a screw, do not substitute a longer screw from a different kit; the LIRIC HEADBAND KIT screws are M2 x 10mm and may not match the 105 AER thread depth. Finally, avoid pulling the ear cups apart by the headband when you put the headphones on; grip the yokes instead to reduce stress on the mounting points.

Caring for the PU leather headband

The 105 AER Headband is made from soft PU leather, which is durable but can dry out or crack if exposed to repeated sweat, hair products, or direct sunlight. Wipe it with a dry or slightly damp cloth after heavy use, and avoid alcohol-based cleaners that can break down the PU coating. Store the headphones on a stand or in a case to keep the band from being compressed. If the PU leather starts to flake or the padding flattens, that is the signal to order a replacement rather than trying to glue or tape it.

Fitting steps at a glance

1. Remove the cable and lay the headphones flat: Unplug the cable so it cannot snag, and rest the 105 AER on a soft cloth with the ear cups facing up. Checkpoint: the work surface should be clean and free of grit that could scratch the cups.
2. Unscrew the old headband with a T6 Torx driver: Turn each screw counter-clockwise and keep them in a tray. Do not force a Phillips driver into the Torx head. Common mistake: stripping the screw head by using the wrong driver size.
3. Fit the new 105 AER Headband with the logo facing outward: Align the yoke holes, thread each screw by hand, then tighten gently. The band should sit centered with equal gaps on both sides. Checkpoint: test the fit on your head before final tightening.
4. Snug the screws and reconnect the cable: Give each screw a final light turn — snug, not tight. Reconnect the cable and confirm the band does not shift when you put the headphones on. Next step: wipe the PU leather with a dry cloth after each session to keep it supple.

Product facts

• 105 AER HEADBAND: Standard replacement headband for the Meze Audio 105 AER, made from soft PU leather with ‘105 AER’ logo engraving. This is the direct-fit part for the 105 AER, so you do not need to modify or adapt it during fitting.
• LIRIC HEADBAND KIT: LIRIC HEADBAND KIT includes a leather headband with Liric engraving, a steel spring band, and six M2 x 10mm T6 Torx screws. Useful if you already own a Liric, but its screws and spring band are sized for the Liric, not the 105 AER — do not assume cross-compatibility.